Vehicles
47 not categorized PORSCHE 924 FRONT CONTROL ARMCan't find what you need? Try browsing the Accessories or Exploded Diagrams!<-- Try narrowing by car using the menu to the left.
$307.70
Make a selection FVD34101807AT By ordering this article number, you will receive a reconditioned wishbone with newly pressed-in bearings. The calculated replacement deposit will be returned to you as soon as the old part has been received and checked. The reconditioning process includes full inspection of each track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we properly install our OEM front control arm bushings, part # FVD341999r. They are made with 65 shore rubber like the original control arms. If your old part is not repairable we will inform you immediately. General Fitment911 1989-94
From $418.00
Make a selection FVD34105304BU2 Diese buchse ersetzt an ihrem vorderen querlenker die hintere buchse. Es handelt sich bei dieser buchse um einen hartegrad von 85 shore wie original bei den rs -modellen ( GT3 rs, GT2 rs ) preis pro stuck, pro querlenker wird ein stuck benotigt.
$108.90
Make a selection 95534158810
View/Change Diagram
From $10.80
Make a selection 91134190201 Is your Porsche pulling from side to side? It is possible your front control arms are damaged. Front control arms steer and help stabalize your vehicle when driving. If these arms become bent, your car will not track straight and true. We stock replacement control arms for all years of 911. View/Change Diagram
From $340.85
Make a selection 95534102702
View/Change Diagram
From $68.34
Make a selection BBI9964010003 Features
$550.00
Make a selection BBI9964010006 Finally, a solution that allows you to safely increase without the risk of damaging your front axles. as you add GT3 shims to your front Porsche 996/997 turbo lower control arms, you move the cv joints beyond their safe range of motion, risking failure and expensive damage. These 10mm thick precision spacers, used with 16mm of lca shims will provide an additional -1.7 deg. Of camber, while maintaining the factory cv joint and axle relationship. the spacer design features a concentric lip that positively and accurately locates it to the cv joint for perfect balance and no vibration. Each kit includes two spacers and all the needed hardware in high class 10.9 grad
$375.00
Make a selection 95534101733
View/Change Diagram
From $186.50
Make a selection EIP072N35S Endless ewig n35s racing front brake pads Porsche Boxster 3.2s 05-07 General FitmentBOXSTER 2005-08BOXSTER 1997-04 911 2005-08 CAYMAN 2006-08 911 TURBO/GT2 2001-05
$526.50
Make a selection ER2071600 Elephant racing low-friction control arm mounts allow for free control arm movement, eliminating any potential for binding. Elephant racing corrected a key factory design limitation:our mounts self-align in all axis, becoming collinear to avoid binding as the arm moves through its range of motion. The low-friction control arm mounts self-align in both the horizontal and vertical planes. The result is collinear front and rear mounts delivering smooth non-binding action. You get superior performance and a smoother ride. Kit includes everything required to upgrade one car. Factory rear mounts are replaced with our self-aligning mounts. Factory front mounts are retained and augmented with self-aligning washers. ...(choose a part on the right to read more) General Fitment911 1965-69911 1987-89 911 1984-86 911 1978-83 930 1975-77 911 1974-77 911 1970-73 914 1970-76 912 1965-69
$225.00
Make a selection EIP071N35S Endless ewig n35s racing front brake pads Porsche 996 turbo 3.6l 01-05 General Fitment911 TURBO/GT2 2001-05911 2005-08
$526.50
Make a selection ER911MNT If you need more front camber adjustment range, these elephant racing offset camberplates are for you. the monoball and mounting holes are offset, allowing up to 3/4 degree of additional camber adjustment range. just the ticket for your race car. These plates use the same spherical bearing technology as our front monoball cartridges and replace the entire factor camberplate. For even more negative camber, combine with our de-cambered ball joints. Combine with polybronze control arm bearings to achieve a rigid front suspension geometry that maintains alignment under hard braking and cornering loads. General Fitment914 1970-76
$499.00
Make a selection FVD34199690 Allows greater camber adjustment possibilities at the front using the 2-piece split control arm set. General Fitment911 TURBO/GT2 2007-09911 GT3 2003-05 911 TURBO/GT2 2001-05 911 1998-05
$2,638.72
Make a selection PAG2707RS14 Pagid rs 14 black front brake pads Porsche 996 GT2 02-05 General Fitment911 TURBO/GT2 2001-05911 GT3 2007-11 911 TURBO/GT2 2007-09
$551.23
Make a selection 90134142102KHD Front; 4pc set of heavy duty stiffer rubber bushings; instructions included
$39.50
Make a selection 95534124204
View/Change Diagram
From $10.00
Make a selection FVD34108400 With age these ducts tend to get battered and broken. They are essential for brake cooling and are a cost-effective diy. They are located right on the front control arms. We also recommend replacing the head bolts that secure the duct as they tend to suffer from corrosion. They are part # 90007402003, 4 are necessary. Add new washers if necessary, part # 49020001, 8 are necessary. Sold as a set. 1 set necessary per car.
$86.52
Make a selection PAG2405RS14 Medium high friction racing compound with high initial bite, excellent release characteristic, very good modulation (controllability) and due to the high ceramic content low heat conductivity. Rs14 has a low wear rate and is fade resistant up to a temperature of 650 deg. C (1,200 deg. F). Applications: touring cars, rally cars (tarmac), GT cars, wsc, dp, single-seaters, nascar . General Fitment911 2005-08BOXSTER 1997-04 CAYMAN 2006-08 911 1998-05
$343.48
Make a selection PAG2488RS14 Medium high friction racing compound with high initial bite, excellent release characteristic, very good modulation (controllability) and due to the high ceramic content low heat conductivity. Rs14 has a low wear rate and is fade resistant up to a temperature of 650 deg. C (1,200 deg. F). Applications: touring cars, rally cars (tarmac), GT cars, wsc, dp, single-seaters, nascar . General Fitment911 GT3 2007-11
$552.65
Make a selection PAG2474RS14 Medium high friction racing compound with high initial bite, excellent release characteristic, very good modulation (controllability) and due to the high ceramic content low heat conductivity. Rs14 has a low wear rate and is fade resistant up to a temperature of 650 deg. C (1,200 deg. F). Applications: touring cars, rally cars (tarmac), GT cars, wsc, dp, single-seaters, nascar . General Fitment911 TURBO/GT2 2001-05911 2005-08
$390.42
Make a selection PAG2488RS15 High friction racing compound with high content of ceramic materials, fade resistance up to 700 deg. C (1,300 deg. F). It combines a 20% higher friction value than the rs14 with a slightly increased pad wear. Although the rs15 has a good controllability and release characteristic it needs finesse to avoid over braking the car, especially with lightweight cars or cars with boosted brakes. Applications: touring cars, rally cars (tarmac), GT cars, wsc, high down-force single-seaters, nascar. General Fitment911 GT3 2007-11
$552.66
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |